| |
|
|
|
 |
Duratec Gray Surfacing Primer |
| Perfect for Plug Finishing and Hiding Repairs |
Duratec Surfacing Primer is the best choice for coating your plug or reconditioning your mold.Thin 5%-15% if necessary to a desired spray viscosity with #2306 Duratec Thinner
after catalyzing. This surface primer can be applied as heavily as 45 mils to fill fabric pores on plugs or over repairs. With a higher heat distortion temperature, shrinkage is reduced. 
This further hides the repair.The gray primer sands easily and is then buffed to a Class 'A' mirror finish before building the mold.
Requires 2% MEKP.
|
|
|
 |
Hard Rubber Sanding Block |
| |
| A Hard Rubber Sanding Block is ideal for removing materials from only high areas until they blend well with the overall surface. This versatile block can be used wet or dry with any grade of paper during rough shaping of the plug or finish sanding the clear gelcoat on a cosmetic repair.
|
|
|
 |
3M Wetordry™ Sponge Pad |
| |
| A 3M Wetordry Sponge Pads are ideal for sanding the entire work surface once it's fair and level. Simply wrap the sandpaper around the pad. Applies even pressure eliminating finger waves in the final finish. |
|
|
 |
3M Wetordry™ Sandpaper |
| Don't Forget This Important Step! |
| Wet sand the surface of new molds to perfection before polishing. This significantly increases the quality and longevity of any mold, and all parts made in it! Using consecutively finer grades of sandpaper from 240-600, any orange peel, texture from PVA, or other imperfections in the mold surface can easily be removed. Also, use for sanding the plug before molding, and leveling of external gel coat repairs. Each combination package includes 240, 320, 400, 500, 600 grit. |
|
|
 |
Step 1 Mold Polish and Step 2 Mold Polish |
| Step 1 - Fast Cut After Sandpaper |
| Step 1 is a water-based polishing compound which begins work where sandpaper stops. 600-1000 grit scratches will rapidly be removed with this fast cutting compound. Step 1 Mold Polish also removes styrene and wax buildup from existing molds. Use this economical compound and achieve great results with only half the normal amount of compound material. Water-base material is safe for use in the paint shop environment. Suggested buffing speed: 2500 rpm min., and a # 1104-A buffing pad is recommended for best results.
Step 2 - Removes Finer Scratches Step 2 Mold Polish will remove finer scratches and polish FRP parts, molds, and even painted surfaces to an exceptionally glossy surface. This economical polish uses half the material to achieve the results from typical compounds. Water-based material is safe for use in a paint shop environment. Suggested buffing speed: 2500 rpm min., and a 1104-A lambs wool buffing pad is recommended for best results. |
|
|
 |
Meguiar's Machine Glaze |
| Step three in the mold polishing sequence |
| This compound conditions the mold surface prior to waxing. #113 eliminates any final swirl marks which may be present at this stage. Additionally, this formula actually 'feeds' the surface with a wax-like petroleum product which deepens the effect of later coats of release wax. This product contains no silicones, making it safe for the paint shop environment. Suggested buffing speed: 2500 rpm min., and a #1104-A lambs wool polishing pad is recommended for best results.
|
|
|
 |
Ultimate Diaper Cloths |
| 3 Panel Cotton Towels |
These super soft cloths are made from best quality cotton. The classic 3 panel construction has a reinforced center panel – just like a diaper! These cloths absorb! They are soft enough for polishing the most critical surface and low-linting so they can be used on windows and glass.
16” x 26”, fully hemmed and machine washable.
|
|
|
 |
Buffing Pads |
| Ideal For Our Polish Compounds |
| This 50% synthetic and 50% lambs wool pad is the recommended buffing pad for our polishing compounds. Do not attempt to use these mold polishing compounds with a foam pad! The #1104-A buffing pad is a great tool for buffing the #1102 Step One Mold Polish, the #1103 Step 2 Mold Polish, and the #113 Meguire's Machine Glaze. This pad will withstand the 2500 rpm minimum buffing speed required for use with all three compounds. Remember, you MUST change pads when changing compounds or the small dust particles trapped in the pad from the previous grade will continue to cut the surface! |
|
|
|
|
Help
Area 
